WARRIOR ASSAULT LOW PROFILE CARRIER V1 MULTICAM
Σε απόθεμα (επιπλέον μπορεί να ζητηθεί κατόπιν παραγγελίας)
Ρωτήστε μας περισσότερα για αυτό το προϊόν
The Low Profile Carrier V1 comes with Solid Side Cummerbunds. The Patent Pending Warrior LPC Low Profile Plate Carrier represents a new generation of armour carriers. Designed with direct input from serving operators within the SF community, the LPC incorporates many new features that combine to make it one of the best carriers on the market today.
The LPC features our new air vent thermo pads, which allows heat to evaporate from the body and increase the airflow to assist in cooling. The Thermo Pad also helps to decrease the back plate signature associated with ballistic trauma.
The LPC utilises state of the art materials to reduce the overall signature and weight. It comes as standard with a removable MOLLE front flap held in place by 2 vertical QASM clips and hook and loop which allows the panel to be removed and replaced with a wide variety of preconfigured panels that are both weapon and mission specific.
The LPC incorporates our speed clip system, which allows very rapid removal of the carrier on a day to day basis, but also in an emergency situation, no complicated cables to worry about, and reassembly takes seconds.
The carrier holds 25cm x 30cm (10″ x 12″) stand alone plates front and back, 15cm x 15cm (6″ x 6″), and 15cm x 20cm (6″ x 8″) side plates and soft armour.
Stand alone plates, 250mm x 300mm (10″ x 12″)and SAPI 238mm x 314mm (9.5″ x 12.5″)
ICW plates 250mm x 300mm and SAPI 238mm x 314mm, with Nexus NIJ 3a soft armour.
All Warrior lightweight plate carriers are designed to work with Nexus style SAPI shaped 10″ x 12″ ( 250mm + x 300mm + ) ballistic plates including bevelled edge ceramic plates and smooth edge composite plates. Steel plates with hard edges and corners should be wrapped to protect the internals of the carriers to avoid excessive wear. Warrior Assault Systems will not be held responsible for any damage to a plate carrier from misuse as stated above.
NIJ Level 3a soft armour
High Quality Threads
Thread quality is fundamental to the construction, durability and strength of tactical equipment.
Two factors have a negative impact on the life Span of threads
1) Mildew is one of the most common factors in the deterioration of military kit, causing it to rot and ultimately results in unacceptable failure.
2) Sunlight has a harmful effect on the performance of threads, and over time causes their deterioration.
Warrior only uses the highest quality US Mil Spec nylon threads imported from the USA which are threated against both UV and Mildew.
- Fiber Resistance to Acid – Good
- Fiber Resistance to Alkali – Good
- Fiber Abrasion Resistance – Excellent
- Fiber Resistance to Heat – 142 deg C (Highest continuous temperature before breakdown)
- Fiber Melting Point – 265 deg C
MIL SPEC Fabric
500D Nylon fabric feature enhanced tear and abrasion resistance, and long lasting durability, 500D Nylon fabric made with solution dyed yarns are inherently stain resistant and easy to clean. MultiCam, Coyote Tan, Ranger Green, Black and A-TACS FG fabrics are all I.R Treated for the lowest signature.
Warrior only uses the highest quality Military rated Clips and accessories.
This product uses MOLLE to connect to other items creating a modular and adaptive system.
* Products may differ from the picture shown due to product improvements over time
This product contains MOLLE webbing that will allow you to attach other pouches using the MOLLE system.
- Genuine US Mil Spec Webbing
- 25mm (1 Inch) Breaking Strain: 1200 lbs
- 38mm (1.5 Inch) Breaking Strain: 1800 lbs
- 50mm (2 Inch) Breaking Strain: 2200 lbs
100% Nylon 500D IR